Month: January 2015

Air Filter | AC Repair Katy

It’s far too easy to overlook changing the air filter in your home’s HVAC system. Not providing filter changes as required can lead to serious problems with your HVAC system requiring AC Repair in Katy or even replacement of the system. Routine filter changes are literally the life of the system.

The reason an overly dirty filter causes is damage is due to two factors, a lack of air and friction. A dirty filter will cause the system to struggle for air, overworking components causing premature wear and tear, and can lead to failure. The stress caused by a dirty filter not only causes premature wear, it increases your energy bill due to the system working overly hard, by up to 15%, and will lead to increased heating and AC Repair in Katy.

Friction occurs when a system struggling for air pulls dust and other damaging particulates into the system around the filter, and will lead to damage to the evaporator coil and other components. Once this material is in the system it creates friction, which causes additional wear on components. Eventually the system fails, leaving your home without heat or cooling, and a system requiring heating and AC Repair in Katy.

Dirty air filters can harm more than just the heating and air conditioning system, it can cause health risks to you and your family. A dirty filter spread dust, dust mites, allergens, mold and other pollutants that can be harmful to your health.

Changing the filter routinely assists in keeping the HVAC system clean, and provides cleaner air for your home. Filters should be changed as often as once per month, depending on the filter type. Keep in mind, air filters increase the longevity and efficiency of the HVAC system by protecting it from dust, dirt and other particles.

How often you should change the filter depends on the type of filter the system uses. While some filters are reusable, others must be replaced. Conditions in the home can also affect the frequency of filter changes, frequent use, pets, smokers, use of a fireplace/wood heater and increased dusty conditions are examples of the need for more frequent filter changes.

Selecting a Filter

There is a significant difference in the quality of replacement filters. Low cost disposable fiberglass filters are the cheapest to buy, though they only capture the largest particles in the air moving through them, and they do almost nothing towards cleaning the air. Better quality disposable pleated filters are more expensive to buy, however they offer a much higher level of filtration. They perform significantly better in protecting the system, reducing the need for heating and AC Repair in Katy, providing cleaner air.

An additional factor that is also essential for homeowner’s to provide is the annual tune-up and inspection of the system. These two factors will ensure the system will last for a number of years.

Permanent Filters

An electrostatic furnace filter must be changed every three months under normal circumstances, and reusable filters can be washed rather than discarded. This creates less waste for the environment, but it also saves you money over time as washable filters can last for a number of years.

Contact your HVAC technician at Cypress Heating and Air Conditioning for questions regarding the proper air filter you should use. To schedule service for issues with your heating and air conditioning give us a call. Our certified technicians provide experienced and expertise for providing maintenance, heating and air conditioning installation, and heating and AC repair in Katy. We serve Katy and the surrounding areas.

Zoned Heating and Cooling System | Heating and Air Conditioning

Zoned heating and air conditioning systems provide specific and individual temperatures for different areas and rooms of the home. For example, the air conditioning can be set to run in hotter areas of the home, and leave it off in cooler areas. If your home experiences differences in temperature, or you would like to reduce energy bills by adjusting the temperature for unoccupied areas, a zoned heating and air conditioning system could provide just the option you desire. A zoned heating and cooling system will provide you with individualized comfort and energy savings.

Conventional heating and air conditioning systems heat or air condition the entire house at the same time. Zoned systems provide the convenience of running the heat or air conditioning in one area of the home, without having to run it in another. Each zone has its own thermostat for a pre-selected temperature in each area.

An additional key feature of zone HVAC is they do not require a duct work system. These systems provide an option for additions to a home where ducts can’t be installed, for homes lacking a duct system that is not a candidate for duct installation, or for homeowners seeking an efficient means of heating and air conditioning their home. Programmable thermostats are compatible with a number Zoned Systems and provide an additional means to cut energy costs even further. An additional way to boost energy savings with a zoned heating and air conditioning system is to select a model with a variable speed blower. Variable speed blowers consume less electricity than standard blower motors, provide an upgrade in humidity control, and operate quieter.

Zoned heating and air conditioning systems operate from a single HVAC system. The system distributes air to the separate zones within a home through the operation of valves, which perform as a damper. Each damper regulates airflow to a specific zone. Zoned systems utilize multiple thermostats, one for each zone. The thermostats operate like any other. They are set to the desired temperature for each zone, and the system cuts on and off as dictated by the thermostat for that zone.

Zoned systems can provide for individual comfort. If one family member is uncomfortably cold when the air conditioning runs, and another is overly hot if it doesn’t, individual thermostats will allow them to set their personal zone thermostat for a comfortable temperature within their own zone, or even a room if set up that way.

Seldom used rooms can be regulated so they are not heated or air conditioned until conditioned air is required. The U.S. Department of Energy estimates homeowners can save up to 30% on energy costs by using zoned heating and air conditioning.

In Summary

  • Zoned systems do not consist of multiple air conditioning or heating units. A zoned system utilizes a single unit with dampers that distribute conditioned air through the designated areas of the home.
  • Each damper is responsible for controlling the airflow to a specific zone within the home according to its individual thermostat setting. Options in organizing zones include by section, floor or by room.
  • Zoned systems utilize several thermostats rather than just one. Each zone will have its own thermostat, and can be set to a different temperature than other zones.

When the air temperature exceeds or goes below the set temperatures, the HVAC system will run. The dampers responsible for a specific zone will generate airflow in that zone until the set temperature is reached, the dampers close when the set temperature is achieved, and the system shuts off.

Cypress Heating and Air Conditioning’s certified HVAC professionals can assess your home for a >strong>Zoned heating and cooling system or other heating and air conditioning systems of your choice. We will ensure you receive the required information to make an informed selection that is right for you. Our certified HVAC technicians will provide a professional heating and air conditioning installation, and ensure that you receive a properly sized system for your home. The professionals at Cypress Heating and Air Conditioning are available 24 hours a day, 7 days a week for emergency heating and air conditioning repair in Katy and surrounding areas.

Furnace Tune-up | Air Conditioning Repair Katy

An annual furnace tune-up is recommended to keep your furnace performing optimally and efficiently. Putting off furnace maintenance affects its peak performance, costing you more for it to operate. In addition, neglecting the furnace can pose health risks to you and your family. A neglected gas furnace can potentially leak deadly carbon monoxide gases into your home. With an annual tune-up, you can be reasonably assured of a well-functioning furnace, safe to operate and performing as efficiently as is possible. An added benefit of providing annual HVAC maintenance is the reduced need for heating and air conditioning repair in Katy.

Gas furnaces produce heat through burning fossil fuels, and it is essential to ensure that the furnace’s combustion process is operating properly and efficiently. Neglecting to provide heating and air conditioning repair in Katy could eventually lead to larger problems. In the case of a gas furnace, it may even develop into a dangerous condition such as a gas leak, or the build-up of dangerous carbon monoxide inside the home. Be safe by having an annual tune-up, and provide any required heating and air conditioning repair in Katy promptly.

During a furnace tune-up, the HVAC technician will check the components of your furnace. By having a thorough, professional inspection and testing provided on the furnace, you can be confident in your furnace providing safe, peak performance throughout the cold winter months. Some of the maintenance tasks provided by your HVAC technician will include:

The Blower

A thorough cleaning of the blower, ensuring it works more efficiently and safely. Cleaning prevents excessive heat buildup in the motor area. Wiring will be inspected for wear, damage or corrosion.

The Motor

The motor will be cleaned of dirt and debris, assisting it in performing optimally and preventing overheating. Motors, which can be lubricated should receive oil annually. This is a special type of oil created specifically for this type of motor. Just a few drops will lubricate the motor and assist it to provide its job for many years.

Ventilation

The ventilation system is checked for blockage and/or leakage. Blocking may occur from leaf debris and nests from birds and squirrels for example. This includes the outside termination (exhaust) and the connections at and internal to the furnace.

Combustion Gases and/or Coils

The combustion gases of a gas furnace must be analyzed to ensure that they meet the unit’s specifications.

Heat Exchanger and Burners

The heat exchanger and burners of a gas furnace are inspected for rust and corrosion. Extensive wear can result in deadly carbon monoxide being released into the home. Burners are also inspected for proper ignition, burner flame and flame sensor. Issues with the heat exchanger and burners require prompt heating and air conditioning repair in Katy due to the risks posed to you and your family. Homes with a gas furnace or other gas appliances should always utilize carbon monoxide detectors.

In an electric furnace the heating coils are inspected for wear, damage and corrosion.

Drainage

When the furnace is part of a heating and cooling system, the AC drainage is inspected for blockage and/or leakage. The condensate drain and trap are cleaned. A number of homeowners have both the heating and air conditioning inspected and tuned up simultaneously with any required heating and air conditioning repair in Katy provided at this time.

Static air pressure tests, gas pressure testing and temperature rise checks are performed as required.

An efficiently running furnace will assist in keeping the energy bill down. Homeowner’s should change the filter monthly, or as recommended by the manufacturer. Furthermore, ensure that you use the recommended filter. Using the “better” filter may result in damage to the system. By regularly changing the filter, you ensure a clean running system and will prolong the furnace’s lifespan. A clean filter and providing professional maintenance are two actions the homeowner can take to extend the longevity of your investment, while maintaining the comfort of your home.

If your system hasn’t received annual maintenance or a furnace tune-up this year, or requires heating and air conditioning repair in Katy, contact Cypress Heating and Air Conditioning to schedule a furnace tune-up. Our certified professional HVAC technicians provide experience and expertise for the care of your furnace. We serve Katy, Plano and the surrounding areas.

Variable Speed Motors | Air Conditioning Repair Plano, TX

Variable speed refers to the indoor blower motor, which moves at the required speed as determined by sensors for precise control of conditioned air. Cypress Heating and Air Conditioning offersHVAC systems with variable speed motors for installation. In addition, it is possible that your existing system is compatible with the technology and may benefit. Contact us for further information, or ask your HVAC technician if your system is compatible when having maintenance or air conditioning repair in Plano, TX.

The Benefits of a Variable Speed Furnace

  • Improved Air Quality: Variable-speed motors with humidistats enable you to control the humidity levels in the home. The relative humidity in a home should be between 30 and 50 percent, for optimal comfort. The consistent airflow of these motors also improves air filtration.
  • Electric Efficiency: Variable-speed motors conserve energy by using less electricity than conventional motors. In fact, the variable speed motor will use approximately one-eighth the electricity operating at half speed than when it runs at full speed. To place its energy efficiency into a different perspective, a variable speed motor at half speed would have to run 8 hours to equal the same amount of electricity consumed by a conventional motor at full speed in 1 hour. As a consequence the variable speed motor can last longer than a conventional motor, reducing the need for heating and air conditioning repair in Plano, TX.

In addition, remember to change the air filter each month, or as recommended by the manufacturer to prevent premature wear and the increased need for heating and air conditioning repair in Plano, TX.

  • Zoning: Variable speed motors and zoned systems are partners in energy efficiency. Zoned systems enable you to control the temperature in different areas in the home. When combined with a variable speed motor that adjusts its output to the speed required, comfort is achieved along with increased energy efficiency, and reduces the need for air conditioning repair in Plano, TX vs. systems with a conventional fan.

How Variable Speed Systems Work

A variable speed motor uses sensors to control the airflow rate. On extremely cold or hot days the motor operates at a higher speed. When temperatures are mildly cool, or warm the motor operates at a slower speed for a longer amount of time. Conventional fans run at one speed, which draws more electricity than a lower speed would. The sensors are designed to give your home the required airflow, saving energy and money when the variable speed motor operates at a lower speed. This process is provided automatically without your intervention, providing a home with optimal comfort and increased energy efficiency.

A variable speed motor isn’t the same as a two or three speed motor. For example, a three speed motor will have three preset speeds for the fan operation. A variable speed motor operates from 0 RPM to full speed and anywhere in between. The HVAC system operates at the precise speed your home requires.

Heating and air conditioning systems remove heat and moisture from the air. When the air conditioning is running, a conventional fixed speed fan runs at the highest speed all of the time. This results in less moisture being removed from the air. A variable speed motor removes a larger amount of moisture from the air than conventional fans. It accomplishes this by running the fan at a slower speed when the air compressor first starts operating, allowing the humidity to be more efficiently extracted from the air.

The air conditioning coil cools the air moving over it, initiating the blower speed to increase and delivering cold, dry air into your home, with a humidity of approximately 50%. Once a balance is established between the humidity and heat loads, the variable speed motor will reduce its speed. In contrast, a conventional motor operates at high speed continuously, causing the air to retain humidity, reducing your comfort, and increasing wear upon the system resulting in increased heating and air conditioning repair in Plano, TX.

Humidity affects comfort by making the air temperature feel hotter than it actually is. In addition, increased humidity promotes the growth of mold and mildew. A variable speed fan motor prevents these issues by limiting the air flow until the moisture is removed from the air and drains out of the drain, rather than ending up in the duct system where mold can grow.

HVAC Products and Services at Cypress Heating and Air Conditioning

Cypress Heating and Air Conditioning carries and installs innovative Carrier products, with a wide range of system options and features, such as variable speed motors. Cypress’s certified and experienced HVAC technicians provide heating and air conditioning installation, service and maintenance, and heating and air conditioning repair in Plano, TX. In addition, Cypress’s professionals’ provide emergency services 24/7, providing you with the heating and air conditioning repair in Plano, TX when you need it most.

Gas vs. Electric Heat | Heating and Air Conditioning

If you are faced with the purchase of a new heating and air conditioning system, you may be debating gas vs. electric heat as the best choice for your home. The answer actually depends upon your climate conditions, and the type of system you select.

Electric Heat

Electric heating sources are great for warmer climates. Electric heat provides clean, comfortable heat without an excessive electric bill, until extreme cold occurs. The air source heat pump can struggle to heat your home when the temperatures are very cold. During frigid weather, back-up heat will be needed when you use a heat pump, and the electric cost will rise. However, there is an efficient heat pump alternative for heating and air conditioning that we will cover later in this blog.

Gas Heat

Gas HVAC systems operate efficiently in sub-freezing temperatures without a loss of heating ability as the temperatures fall. However, many persons are uncomfortable with the risks that natural gas poses. The main risks of gas are explosion and fire. Additional risk factors include carbon monoxide poisoning and asphyxiation. The occurrence of an explosion and fire are very low, and all of the risk factors become minimal when annual maintenance and tune-ups are provided, and carbon monoxide detectors are installed and maintained.

An additional factor that must be considered for gas heat is the cost of gas in your area. The cost can vary widely, with gas providing a very economical selection for some areas, and excessively priced in others.

Combined Technology

As previously mentioned, there is an alternative that provides the best of both options. The installation of a hybrid heating and air conditioning system will provide both gas and electricity for heating. You will enjoy the benefit of electricity’s efficiency during milder temperatures, and the system will automatically provide your home with the warmth you require during sub-freezing temperatures.

The hybrid system utilizes sensors to determine which heating source is appropriate for the current conditions, directing the operation of either the gas furnace or the electric heat pump. This enables you to maintain comfort without excessive operating costs.

Hybrid Systems Provide Cooling

It is like having three systems in one, with all components neatly packaged into one outdoor unit. The system provides two energy sources that are automatically controlled, providing optimal heating, while the heat pump also operates as an air conditioner for energy efficient cooling during the sweltering summer months. It provides the best of both worlds in heating and air conditioning, maintaining your family’s comfort and operating efficiently and cleanly.

This arrangement is especially beneficial for homes with limited indoor space. The ability to install a packaged hybrid heating system will depend on your current HVAC configuration and your home’s structure. In addition, the hybrid system is available as a split system for those who already have a split system AC and a furnace.

An additional factor that must be considered for either hybrid system is the access to natural gas. If your home isn’t already equipped for gas appliances, the hybrid solution may not be an option. If natural gas is available, but simply not installed in your home, a gas supply can be provided, enabling you to take advantage of the hybrid split system.

Cypress Heating and Air Conditioning’s professional HVAC technicians offer the experience and expertise you require for efficient and reliable heating and air conditioning services. We offer 24 hour emergency service for your comfort, and air conditioning repair, maintenance and installation. If you require assistance in selecting a new HVAC system for your home, or would like assistance in the decision of gas vs. electric heat, we will be glad to assist you, and /or provide an estimate for installation.

Furnace Problems | Air Conditioning Installation

There is a lot being said about energy efficiency, and a number of homeowners are concerned with receiving the most energy efficient heating and air conditioning system that their budget will allow. However, when a furnace breaks down on the coldest day of the winter furnace repair is the typical choice rather than replacement with heating and air conditioning installation in a cold house. Cypress Heating and Air Conditioning professionals can diagnose and repair your home’s furnace problems.

Furnace Replacement

The best time to select a new HVAC system is before a breakdown occurs. The Katy/Plano region seldom experiences the extreme cold of more northern climates, and this means an energy efficient alternative for Katy is a heat pump.

An advantage to installing a heat pump is that you are not only receiving a new heating system, but a new cooling system as well. In one neatly packaged system, you are receiving both heating and a air conditioning installation.

When you are considering alternatives for furnace replacement, and desire energy efficiency, reliability and clean comfort, talk to your HVAC technician about a heat pump.

Furnace Repair

As the weather gets colder, your furnace is likely to cycle more frequently. However, short cycle lengths can indicate a problem with the heating system. Short cycling is different from the normal increased cycling that occurs with colder temperatures. Short cycles occur when the furnace repeatedly cycles off and on without adequately heating your home. In other words, the furnace doesn’t run long enough to heat your home up before it cuts off. Cypress Heating and Air Conditioning’s reliable technicians can provide the expert repair or the professional heating and air conditioning installation that you require.

Causes of Short Cycling

There are several aspects of your heating system that could lead to problems with short cycling. These include:

  • Air flow – Dirty air filters is a frequent cause of HVAC malfunctions. The filter is your system’s first line of defense against damaging dust. When a filter isn’t changed properly, dirt clogs up the filter until air is unable to move through it. The second impact of a dirty filter is dirt being sucked into the system as it struggles to draw air from every crack and crevice. Damage to the system components are the result of a dirty filter, and changing a dirty filter may correct your furnace’s short cycling.
  • Controls – Thermostat issues can impact the cycles. Bad batteries may be causing the issue, thermostat adjustments may be required, or the thermostat may need to be replaced. Check the batteries if applicable, otherwise contact your HVAC technician for thermostat issues and short cycling. Thermostats must be compatible with the HVAC system, and when it is time for a new heating and air conditioning installation a compatible thermostat is essential.
  • Sensors and safety mechanisms – Blocked ventilation or bad internal components may be at the root of the problem. The assessment of these factors should only be provided by a certified professional due to the risks to your family if either is involved. Unintentional damage from DIY repair could compromise your family’s safety.
  • Ventilation – Blocked ventilation can cause problems with HVAC systems, and is a dangerous condition when the furnace is gas. All homes with gas appliances should have carbon monoxide detectors, with at least one on each floor, and detectors located near bedrooms. If your carbon monoxide detectors are alarming, evacuate your home of all occupants. Once the gas supply is shut off to the home provide fresh air ventilation by opening windows, and call for expert repair.

Annual Maintenance Saves Money

As you resolve your short cycling issue, you should consider making pre-season furnace maintenance a priority in the coming years. You can reduce breakdowns by having your furnace thoroughly inspected and tuned up prior to the onset of the heating season. Preventive annual maintenance will lower your winter heating costs, while extending the life of the system.

This is especially beneficial for a new heating and air conditioning installation. Annual maintenance will maintain peak performance, energy efficiency and provide a longer lasting system when provided routinely from the start. Even aging systems past their prime will benefit, but a new system routinely serviced will benefit even more by avoiding the increased wear due to neglect.

Cypress Heating and Air Conditioning professionals take pride in providing expert service, whether you need repairs for furnace problems, maintenance or heating and air conditioning installation. Our certified and experienced technicians can evaluate your home and provide you with the best solution for efficient and affordable heating and air conditioning. We offer American made Carrier products for your next heating and air conditioning installation. Cypress Heating and Air Conditioning professionals serve Katy, Plano and the surrounding areas.

Tips to Improve Indoor Air Quality | Air Conditioning Service

During the winter, cold reduces our time spent outdoors, and results in homes being tightly closed, preventing fresh air from entering the indoor environment. This reduces indoor air quality until warmer temperatures arrive. When your HVAC system is contributing to indoor air pollution, contact our certified technicians to receive heating and air conditioning service. Read the following for tips to improve indoor air quality.

While air pollution is typically associated with outdoor air, according to the EPA, indoor air pollution can be up to five times higher than outdoor levels, and in some cases as much as 100 times higher.

It pays to take action to improve indoor air quality, as your family’s health is at risk.

Where Indoor Air Pollution Comes From

Modern homes are designed to be energy efficient with little if any air exchange between indoor and outdoor air. Without ventilation and other measures, it is likely that you are breathing polluted air.

Common sources of indoor pollutants include:

  • Air fresheners (a number of these products contain VOC’s)
  • Building materials
  • Carpeting
  • Cabinets or furniture made of pressed-wood products
  • Cigarette Smoke
  • Central air conditioning and heating systems – Providing routine heating and air conditioning service will ensure the proper operation of the HVAC system, reducing any potential contaminants from the system, and aiding it in filtering contaminants from the home’s air.
  • Combustion sources of fossil fuels (oil, gas, kerosene, coal and wood)
  • Hobby materials (glues, epoxy, spray paints, paint strippers, etc.)
  • Household cleaning products
  • Personal care products
  • Pesticides
  • Radon

Common complaints related to biological pollutants include allergic symptoms such as sneezing, watery eyes, coughing, and shortness of breath. Additional symptoms include fever, digestive problems, eye, nose and throat irritation, fatigue, headaches, and dizziness.

Tips to Improve Indoor Air Quality

The following tips will assist you in minimizing indoor air pollution:Reduce the Sources: Avoid spraying pesticides, chemical cleaners, air fresheners and other potential pollutants in your home. Look for products with low or zero VOC labels.When purchasing furniture, carpeting, cabinetry or flooring, look for those made of green building materials, as these won’t release VOC’s. Check for low-VOC or zero-VOC labels.

Increase Ventilation: Few heating and air conditioning systems provide fresh air in the home. Newer homes may have air-to-air heat exchangers, which bring outdoor air into the home while providing energy efficiency. Providing professional annual heating and air conditioning service will ensure the proper operation of your home’s system. Furthermore, professional duct cleaning will improve the indoor air quality. Together, these services will ensure your homes HVAC system isn’t contributing to indoor air pollution while ensuring an extended service life, and reducing the need for repair and additional heating and air conditioning service.

During warm weather it is easier to provide ventilation by opening the windows or using window or attic fans. During cold weather use kitchen and bathroom exhaust fans, and change your HVAC systems filter once per month, unless otherwise directed by the manufacturer. Routine filter changes extend the system’s service life, provide cleaner air, maintain a cleaner HVAC system and reduce the need for air conditioning service and repair.

Furthermore, ensure you use the recommended filter type to avoid stress upon the system, increasing the need for air conditioning service and repair.

Test Your Home for Radon:

Radon is an insidious toxin, and is undetectable unless the home is tested for it. Consider testing your home, and if detected take the appropriate steps.

Control Humidity:

Maintaining a humidity level between 30-60 percent will help to keep dust mites, mold and mildew under control. A Cypress Heating and Air Conditioning technician can provide the professional installation of a whole house humidifier.

Reduce the moisture level in the bathroom by providing adequate ventilation with a quality exhaust fan. Allow it to run for 20 minutes after showering to thoroughly dry accumulated moisture preventing mold and mildew.

Provide Routine Cleaning: Routine dusting and vacuuming of your home will help to control dust mites, pollen, dander, and other biological air pollutants.

Consider an Air Cleaner:

Air filters and cleaners will assist in removing contaminants from the home’s air. A whole house system will be the most effective. Circulation rate and the efficiency rating are important factors to consider when selecting an air cleaner. A Cypress Heating and Air Conditioning professional can assist you in the selection of a system that will be efficient for your home.

Preventing Dry Winter Air

Forced-air heating systems lead to dry winter air in homes. The dry air irritates the mucous membranes of the nose and throat, causes dry itchy skin, nosebleeds and chapped lips.

Furthermore, cold, dry air promotes the flu viruses which flourish in cold, dry air facilitating its spread and the length of contagion. A humidity level of 30-60 % will help to keep the side effects of dry air – and the flu at bay. Ensure humidifiers are kept clean with fresh water added each day to prevent the growth of mold and microorganisms in the humidifier.

If your HVAC system hasn’t received heating and air conditioning service in a year or more, schedule service today to ensure its proper operation and maximum efficiency.

These tips to improve indoor air quality will assist you in achieving cleaner air in your home. Cypress Heating and Air Conditioning’s certified HVAC professionals provide experience and expertise for reliable heating and air conditioning service, installation and repair. Contact us to receive the cleanest indoor air quality possible for your home. We serve Katy, Plano and the surrounding areas.

Heat Pumps | Heating and Air Conditioning

Heat pumps are popular HVAC systems that offers Texans heating and air conditioning in a single system. Keep reading to find out which heat pump features are right for your Texas home.

Two-Stage Heat Pumps

The compressor and air handler are fixed-stage components in conventional air-source heat pumps. This means they operate at 100 percent capacity all the time. Today’s heat pumps offer you options for greater efficiency and improved comfort.

Two-speed heat pumps utilize a compressor and air handler that offer an additional lower speed, typically 60-percent capacity, in addition to full capacity capability when required. Two-stage systems are more efficient and provide greater comfort. Variable-Speed Heat Pumps

An additional option is heat pumps that use variable-speed air handlers and scroll compressors for maximum efficiency and comfort. Scroll compressors are rather simple in design, and adjust air velocity as it is required. This enables these heat pumps to maintain thermostat temperature settings to within less than one degree. The simple design of the scroll compressor provides fewer moving parts for reduced noise and increased reliability when compared to conventional compressors and air handlers.

Are Heat Pumps Less Efficient in Extreme Cold?

Today’s heat pumps are not the same as the one your grandparents owned. Heat pump technology has significantly improved in energy efficiency and will continue to do so in the future. In fact, many of today’s net zero homes utilize the heat pump for their HVAC system.

If you are considering a heat pump you may worry that the system will suffer a loss of efficiency in the heating mode when temperatures drop too low. It is true that the former heat pumps had difficulty with extremely low temperatures. In the past, homes with heat pumps depended solely on strip heat to provide heat to a home when the temperature dropped below the heat pumps tolerance. Strip heat was similar to having an electric furnace kick in when the temperature threshold was met, and the heat pump was unable to produce adequate heat.

Since those days, heat pump technology has improved, providing better performance. Furthermore, a hybrid heat pump offers a solution for areas with occasional extreme cold. These systems combine a heat pump with a back-up heater that uses a separate fuel source, usually a gas furnace. These systems automatically kick in when temperatures fall below the set threshold, with the auxiliary heat taking over the task of heating your home.

For many southern homeowners, a heat pump provides an energy efficient heating and air conditioning system that operates cleanly, and provides superior comfort year round.

Heat Pump Maintenance

Annual maintenance of your heat pump by a certified HVAC technician will maintain proper operation and efficient performance, while extending the system’s service life.

Homeowners can ensure a cleaner system by changing the filter once a month or as recommended by the manufacturer. Filters manufactured to be cleaned and reused should be cleaned each month. Dirty filters can result in dirty coils, and fans. This reduces the airflow through the system and will decrease the system performance, while increasing wear and tear upon the unit.

In addition, ensure that you use the recommended filter. The use of a HEPA filter in a system not engineered for it can result in premature wear on components due to its inability to pull air through the HEPA filter.

When considering a heat pump for your home, talk to your HVAC technician regarding your options. For most homes, the heat pump will provide the energy efficient heating and air conditioning option that you desire.

Cypress Heating and Air Conditioning offer a full line of quality heating and air conditioning systems, including quality heat pumps. Our certified HVAC technicians provide exceptional service and are dedicated to exceeding your expectations and providing your satisfaction. Our experienced professionals offer heating and air conditioning repair, service, and installation. We serve Katy, Plano and the surrounding areas.

Programmable Thermostats | Air Conditioning Katy, TX

The thermostat is a component of a home’s heating and air conditioning in Katy, TX. The thermostat regulates the home’s temperature winter and summer, maintaining it on the selected setting. All thermostats will eventually wear out, resulting in the need for replacement. An energy saving alternative for homeowners who must replace a worn thermostat, or for those who would simply like to save money on energy costs, is a programmable thermostat. These versatile thermostats enable the settings to be customized to your schedule, eliminating unnecessary energy waste.

You can save money on the energy costs of heating and air conditioning in Katy, TX by resetting the thermostat when you’re asleep or away from home. However, most of us will forget occasionally, and these lapses cost us money. With a programmable thermostat, temperature adjustments are provided automatically according to a pre-set schedule that you provide. This provides a consistent savings that add up to cold, hard cash.

In addition, programmable thermostats can store and repeat multiple daily settings (six or more temperature settings a day) that you can manually temporarily override without affecting the rest the programmed schedule.

Recommended Thermostat Operation

Setting the thermostat to 68°F while you’re awake, and to 65°F while you sleep will save on energy costs. When you’re away from home, a setting of 55°F will prevent frozen pipes while increasing your savings. Turning the thermostat back 10° to 15° for 8 hours will save 5% to 15% a year on the heating bill. This provides a savings of approximately 1% for each degree.

During the summer, you can reduce the costs of air conditioning in Katy, TX by keeping your house warmer than normal when you’re away, and maintaining the thermostat setting to 78°F when you’re home. Programmable thermostats will provide the temperature adjustments automatically, eliminating any discomfort by adjusting the temperature to the setting for when occupants are present before you wake or return home.

Programmable thermostats offer the additional benefit of reducing wear and tear on your home’s heating and air conditioning in Katy, TX , by reducing unnecessary run time.

Heat Pumps and Thermostats

Until recently, programmable thermostats were not recommended for heat pumps. In its cooling mode, turning up the thermostat on a heat pump will save energy and money. However, when a heat pump is in its heating mode, setting back the thermostat can cause the back-up strip heat to operate, resulting in increased energy usage. Maintaining a moderate setting is the most cost-effective practice. However, specially designed programmable thermostats for heat pumps are now becoming available, enabling setting back the thermostat on heat pumps more cost-effective. These thermostats use special algorithms to minimize the use of backup electric heat.

Choosing and Programming a Programmable Thermostat

Digital thermostats offer the most features in terms of multiple setback settings, overrides, and adjustments for daylight savings time, but may be difficult for some people to program.

The location of the thermostat can affect its performance and efficiency. To operate properly, a thermostat must be on an interior wall away from direct sunlight, drafts, doorways, skylights, and windows. Don’t place furniture in front of your thermostat as this will block natural air movement and result in poor performance. Ensure the thermostat is conveniently located for programming.

Smart Thermostats

Smart thermostats provide more advantages than just temperature control and energy management. They can communicate with your smart home to accomplish other beneficial tasks.

Smart Thermostat vs. Programmable Thermostat

A programmable thermostat is essentially any thermostat that uses a built-in clock to control the temperature in your home. Programmable thermostats allow you to create custom schedules that correspond to the preferences that you manually programmed.

Smart thermostats are programmable thermostats that have been enhanced with additional features. These features include automatic schedules, the ability to adjust the thermostat remotely, to be notified when the thermostat is manually activated, and energy savings reports that guide you to energy efficient settings for your heating and air conditioning in Katy, TX. A smart thermostat detects and adapts to your schedule with little effort on your part.

Wi-Fi connectivity enables you to control the thermostat remotely, and the smart thermostat is capable of much more. For example, a smart thermostat will work in conjunction with home automation. For example, with compatible home sensors the thermostat can be programmed to cut off when a door is left open, or to go into its unoccupied mode when you lock the door on your way out. Some models of smart thermostats will even work with a security system, turning compatible LED lights on and off randomly, making your home appear as if it is occupied.

Homeowners with DIY skills can potentially install a thermostat. For those who prefer a professional installation, Cypress Heating and Air Conditioning offers professional installation of a programmable thermostat or a smart thermostat that is compatible your heating and air conditioning in Katy, TX.

These are but a few examples of the possibilities provided by a smart thermostat. Features will vary according to model. Our professionals provide reliable services for heating and air conditioning in Katy, TX including repair, installation and maintenance. Furthermore, our certified technicians have the expertise to meet or exceed the industry’s standards, assuring you of receiving quality HVAC services.

For the professional installation of a programmable thermostat compatible with your heating and air conditioning in Katy, TX, contact the professionals at Cypress Heating and Air Conditioning. We serve Katy, Plano and the surrounding areas.

HVAC Repair | Heating and Air Conditioning

From power surges to dirty filters there are numerous factors that can result in a home’s heating and air conditioning system requiring repair. However, some causes are more common than others, and of these, some are preventable, while others are not. In the following we will discuss the four most common issues that result in the need for heating and air conditioning repair in Plano, TX. Contact Cypress Heating and Air Conditioning for your HVAC Repair and installation needs.

Lack of Maintenance

You have invested your money in the most energy efficient heating and air conditioning system possible for your home. It stands to reason that you want to provide the care the system requires to extend its service life. Periodic maintenance is essential to maximize the HVAC systems service life, while maintaining peak performance and the energy efficiency that you selected it for. Neglecting to provide professional and routine maintenance will result in an increased frequency of breakdowns, increased energy cost, poor performance and the premature demise of the unit.

Dirty Filters

Replacing the filter in your furnace as recommended is one of the most important things you can do to extend the life and efficiency of your furnace. Economical blue filters should be changed each month while pleated filters recommend changing every three months. However, homeowners should realize that increased dusty conditions can result in the need for more frequent filter changes. A good rule of thumb is to check the filter each month and change as required.

A dirty filter will restrict the air flow, causing the system to work harder to pull air through the filter and into the circulation through your home. This puts unnecessary strain on the furnace and results in premature wear and tear on the system, as well as the risk of damage or fire due to overheated components.

Mechanical Wear

The furnace contains numerous components that collectively provide the heating that you depend upon for your home. Wear and tear on any one of these components may cause issues with the performance of the heating and air conditioning system. Over time wear and tear will occur as the system ages, even with proper care. However, this wear can be reduced, and the system’s service life extended when proper care is received.

Thermostat Malfunctions

The thermostat is the separate component of the HVAC system that controls and determines when the system operates to produce heat, and when it shuts off. As with any other mechanical device, the thermostat will eventually wear out and require replacement. Problems with the thermostat can result in no heat, too much heat, insufficient heat or the failure of the fan to operate. If you find yourself making numerous trips to the thermostat to turn the heat up or down, it is likely the thermostat needs to be replaced.

Cypress Heating and Air Conditioning’s NATE certified technicians can accurately diagnose your furnace problems and provide the required furnace repair. We care about your comfort and safety. Keep in mind that annual maintenance of all heating and air conditioning systems is recommended. This is especially important for a gas furnace. The gas fired furnace may pose safety hazards due to combustion or gas and the risk greatly increases when not properly maintained on a periodic basis. If your furnace has not received maintenance this year, call now for service. Professional maintenance ensures your safety, and can help to keep energy costs down.

Cypress Heating and Air Conditioning’s certified HVAC technicians provide exceptional service and are dedicated to your satisfaction. Cypress Heating and Air Conditioning offers experience and expertise in heating and air conditioning installation, repair, annual maintenance, and more. We serve Katy, Plano and the surrounding areas.

Air Conditioner Repair Spring, TX